Pressure relief of underground ammunition storage under missile accidental ignition

Safety of underground ammunition storage is an important issue, especially during the accidental ignition of missiles. This work investigates the pressure and temperature distribution of the multi-layer underground ammunition storage with a pressure relief duct during the accidental ignition process of the missile. A large-scale experiment was carried out using a multi-layered restricted space with a pressure relief duct to simulate the underground ammunition store and a solid rocket motor to simulate the accidental ignition of the missile. The results show that when the motor gas mass flow increased by 5.6 times, the maximum pressure of the ammunition storage increased by 5.87 times. At a certain motor flow rate, when the pressure relief exhaust area at the end of the relief duct was reduced by 1/2, the maximum pressure on the first layer did not change. But the rate of pressure relief was reduced and the time delayed for the pressure of ammunition store to drop to zero. In this experiment, when the motor ignition position was located in to the third layer ammunition chamber, the maximum pressure was reduced by 32.9％ and also reduced the rate of change of pressure. In addition, for the experimental conditions, the theoretical analysis of the pressure relief of the ammunition storage is given by a simplified model. Based on the findings, some suggestions to the safety protection design of ammunition store are proposed.     

A melt-cast Duan-Zhang-Kim mesoscopic reaction rate model and experiment for shock initiation of melt-cast explosives

A melt-cast Duan-Zhang-Kim (DZK) mesoscopic reaction rate model is developed for the shock initiation of melt-cast explosives based on the pore collapse hot-spot ignition mechanism. A series of shock initiation experiments was performed for the Comp B melt-cast explosive to estimate effects of the loading pressure and the particle size of granular explosive component, and the mesoscopic model is validated against the experimental data. Further numerical simulations indicate that the initial density and formula proportion greatly affect the hot-spot ignition of melt-cast explosives.     

Experimental investigation on enhanced damage to fuel tanks by reactive projectiles impact

Enhanced damage to the full-filled fuel tank,impacted by the cold pressed and sintered PTFE/AL/W reactive material projectile(RMP)with a density of 7.8 g/cm3,is investigated experimentally and theoretically.The fuel tank is a rectangular structure,welded by six pieces of 2024 aluminum plate with a thickness of 6 mm,and filled with RP-3 aviation kerosene.Experimental results show that the kerosene is ignited by the RMP impact at a velocity above 1062 m/s,and a novel interior ignition phenomenon which is closely related to the rupture effect of the fuel tank is observed.However,the traditional steel projectile with the same mass and dimension requires a velocity up to 1649 m/s to ignite the kerosene.Based on the experimental results,the radial pressure field is considered to be the main reason for the shear failure of weld.For mechanism considerations,the chemical energy released by the RMP enhances the hydrodynamic ram(HRAM)effect and provides additional ignition sources inside the fuel tank,thereby enhancing both rupture and ignition effects.Moreover,to further understand the enhanced ignition effect of RMP,the reactive debris temperature inside the kerosene is analyzed theoretically.The initiated reactive debris with high temperature provides effective interior ignition sources to ignite the kerosene,resulting in the enhanced ignition of the kerosene.     

铝导线短路熔珠对固体可燃物引燃能力实验研究

在模拟试验平台上进行了铝导线短路熔珠引燃棉布、聚氨酯泡沫塑料和纸张的试验，得到了不同材料的临界加栽电压值和引燃规律。初步分析了加栽电压与短路熔珠粒径及引燃能力的关系。结果表明，随着短路电压增大，导线熔珠的粒径逐渐增大，熔珠对固体材料的引燃能力逐渐增强，氧指数越低、表面粗糙、易蓄热的材料越容易被点燃。棉布、聚氨酯泡沫塑料和纸屑被引燃的短路临界电压分别为50V、35V和45V。     

固体发动机尾部点火性能影响因素分析

采用准一维非定常数值模型,对某小型固体发动机尾部点火瞬态过程进行性能预示;以预示结果为基础,对尾部点火性能主要影响因素进行了参数研究.研究结果可为尾部点火器和喷管堵盖的点火匹配性设计提供有益指导.     

导线过负荷引燃能力的模拟实验研究

为了考查导线过负荷对不同可燃物的引燃能力，选择1．5,2．5和4mm^2三种规格的铝导线在不同倍数过负荷电流条件下进行实验，测得导线温度并观察过负荷导线对火场中常见的棉布、阻燃管、防水板的引燃能力。通过实验得出过负荷导线引燃能力与导线截面积、过负荷时间、过负荷电流的大小的关系，并讨论了可燃物种类对过负荷导线引燃能力的影响。结果表明，过负荷导线的引燃能力与过负荷电流和时间成正比，而导线的截面积对引燃能力的影响是多方面的。为防止火灾发生，在建筑物中布置导线时要远离可燃物并要穿阻燃管铺设。     

有线控制飞行器群脉冲耦合效应及加固方法研究

飞行器在飞行状态时，控制导线在电快速瞬变脉冲群（EFT）作用下，该设备控制指令将会出现控制状态错误翻转、持续无指令输出等故障，产生故障的机理是电磁脉冲（EMP）通过传导方式进入控制箱产生紊乱的回输信号所致，严重时会损坏控制器及起飞装置。在实验基础上，研究了飞行器控制导线对电磁脉冲的防护加固方法，研究结果表明，对控制导线采取屏蔽法能够使飞行器对电磁脉冲具有很好的防护效果。     

转子碰摩情况下瞬时转速变化规律的仿真研究

考虑到碰摩会造成转子瞬时转速波动的实际情况,对已广泛应用的弹性模型进行了改进,建立了考虑转子瞬时转速波动的转子碰摩仿真模型。利用该模型仿真计算了不同转速下轴心轨迹和瞬时转速波形、频谱,发现在碰摩严重程度不同的情况下,转子瞬时转速有着明显的规律性变化。     

阻化烟煤堆非稳态温度场计算

依据实验测得的干、水湿和阻化烟煤氧化反应的动力学参数 ,引入了氧传质模型和水蒸气平衡模型 ,利用计算机编程对干、水湿和阻化烟煤堆内的一维非稳态自热过程的模型分别进行差分计算 ,求得相应煤堆内的非稳态温度场。结果表明 ,采用简化的一维自热过程的非稳态数学模型计算 ,可以剖析氧传递、水蒸气平衡和阻化处理对煤堆自热的影响 ,可以评价实际煤堆的自热危险性和判断烟煤堆的阻化处理效果     

室内装饰织物燃烧特性研究

室内装饰织物因其容易点燃、燃烧速度快、蔓延迅速等燃烧特性,对室内火灾的发展蔓延及火灾危害都有重要影响。运用锥形量热仪对棉麻、涤纶、帆布、泡纱、条绒等5种室内装饰织物的燃烧性能进行了实验研究,测量了室内装饰织物在不同热辐射条件下的燃烧特性,并对实验数据进行图像拟合,通过具体的实验数据和图像分析比较了5种室内装饰织物在不同热辐射条件下的点燃时间、热释放速率、质量损失速率、比消光面积及CO生成量。最后得出了各种织物的火灾危险性相对大小。